Fabric Gift Bag/Scrap Bin Tutorial

After making the toy bins for my little guy’s toy ( and saving my feet from the inevitable midnight toy stomp), one very smart commenter thought that a smaller version would make a great scrap bin! I thought that was a great idea, and took it a step further. Presenting the Fabric Gift Bag……

Fabric Gift Bag

…that turns into a scrap bin!!

Scrap bin!

The bin finishes at 5″x5″x5″ ( who doesn’t like perfect squares!)

 

Supplies

An 8″x20 1/2″ rectangle of the outer fabric and heavy weight woven fusible interfacing

An 11 3/4″x20 1/2″ rectangle for the lining

A square ruler ( no larger than 6 1/2″) or a hard piece of template material 2″x2″ square.

Your various sewing paraphernalia ( scissors, needles, thread, band-aids, coffee…)

Supplies

Instructions

1. Fuse the interfacing to the wrong side of the outer fabric.

2. Match the shot raw edges and stitch a 1/4″ seam across, backstitching at either end.  ( all seams will be 1/4″)

3. Sew the bottom raw edge from the fold to the seam, backstitching at either end. Trim your seams to 1/8″ and set aside.

4. On the short side of the lining make a mark 3/4″  and 1 1/2″ from the top. Stitch from the top to the first mark and stop. Move to the second mark and resume stitching your seam to the bottom. Press this seam open.

Leave this open. This is the TOP

5. Stitch the bottom seam of the lining ( furthest from the opening in the seam), backstitching at both ends.

NOW THE FUN PART

6. Take your outer fabric with the interfacing side out. line up the 2″ square line with the stitched seams as shown and mark a line around. If using the template line up the corner of the template to the stitching lines on the inside. Mark your lines. Repeat for the opposite side, lining up the fold  and the stitched line with the 2″ line.

Lined up for marking

Marked Lines

7. Cut on the marked lines. Repeat the steps for the lining. It should look like the picture below

Cut out

8. Bring the raw edges of the cut out squares together on either side, matching the center fold and bottom seam on one side and the bottom seam and side seam on the other. Sew the raw edges and trim the seam allowances. Repeat for the lining.

Match the raw edges of the square

Match the bottom seam to either the fold or the side seam and pin.

Sew a 1/4″ seam along the raw edges

9. Turn the outer bin right sides out and place right sides together inside the lining bin, matching the raw edges and the side seam. Sew all the way around the top, leaving a 2″ gap for turning.

Turn right side out

Place inside the lining, matching seams, and sew 1/4″ seam, leaving a 2″ gap for turning.

10. Turn the bin right side out through the opening. Use your favorite stitch to hand sew the opening closed.

Close the gap

11. Push the lining into the main body of the bin snugly and finger press into the seams. You will have 2″ extra of the lining folded overto the main body of the bin.  Press the top fold of the lining and the inside of the bin.

Extra fabric. Press the top fold all the way around

12. Edgestitch around the seam connecting the lining to the main bin.

13. Insert a ribbon or cording through the opening you left in the seam of the lining. I used a hook to push the ribbon as far in as i could, wrangled it off, then inserted the hook in the other direction, hooked the ribbon and pulled it the rest of the way through. It seemed like a good idea at 11:30 at night. Your best bet is to use a tapestry or cross stitch needle ( one with a dull end), and use it to pull a ribbon through, or thread it and knot the thread, pull the thread through the cording or ribbon, and then feed it through using the needle.

Find the opening

Feed the ribbon through.

14. Tie the ends together in a slipknot close to the opening, leaving about a 1″ tail. This will ensure the ribbon is hidden when in Scrap Bin mode.

Voila! You are finished your Gift Bag/Scrap Bin!!

Gift Bag Mode

Scrap Bin Mode

Gift Bag Mode: Pull on the end of the ribbon and draw up the band of fabric. Tie a bow!

Scrap Bin Mode: Release the bow and pull the edged of the band taught. Fold down over the main body of the bin.

I hope you enjoy making a bunch of these for your friends and yourself! They come together very quickly and the possibilities are endless! You could always fill one with cookies and send it my way! Yum Yum!
As always,

Happy Sewing!!

One thought on “Fabric Gift Bag/Scrap Bin Tutorial

Leave a Reply